The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
We've noticed this post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and concluded it made good sense to talk about it with you over here.
Setting up a tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably hard project. If the old tub is readily obtainable, the task can relocate easily; if you have to open up a wall to remove the old bathtub and place the new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a specialist to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will assist you install a new bath tub in your bathroom if you have currently gotten a new bathtub and don't require to transform the setup of your previous supply of water pipes.
Your devices and also product list should comprise the following:
Planning for the Setup
To start with, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you ought to do is detach the water supply. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the limited gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, position the bath tub in the needed setting. The wooden boards are valuable in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the bathtub up until the level reviews degree.
To install faucets, fit the bottom of the furthest flexible faucet connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water supply and examine all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill up the bath tub as well as likewise examine the overflow outlet and also the regular outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait till the bath tub has actually been used a minimum of once as this will settle it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the faucet and also the sink. Secure the faucet in place with the producer offered backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The former kind needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack an inflexible seal, triggering the water to penetrate the wall between the bathroom and the tiling, leading to issues with moisture and also possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can split rather very early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that article about Installing A Bathtub through an associate on another site. Liked our posting? Please share it. Help another person find it. Thanks so much for going through it.
Urgent support required? Report this page